Call to reach a local rooferNew Haven, CT
Call (833) 751-2102
Call to reach a local rooferCall any time(833) 751-2102
Serving New Haven County

Where the roof meets the chimney on an older house

The metal around a chimney is renewed as a set, with counterflashing let into the masonry rather than sealed onto it.

  • Wind and storm damage
  • Ice dams after winter storms
  • Shoreline wind exposure

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

Chimney Flashing

Chimney Flashing Repair: what it covers

Quick answer

Chimney flashing repair renews the metal that joins a brick stack to a roof: the apron at the front, the step pieces up each side, the back pan or cricket, and the counterflashing cut into the mortar joints above. New Haven Roofing connects New Haven and New Haven County callers with a local roofer for this work.

Chimney Flashing Repair illustration for New Haven, CT

A chimney is a hole in the roof with a wall built through it. The roof covering cannot be carried across it, so the junction is made entirely of metal, and that metal has to deal with water arriving from above, running down the masonry, and being driven sideways at it by wind. It is the single most demanding detail on most pitched roofs.

Brick stacks are everywhere on the housing here. Where well over a third of the city's homes predate World War II by its own housing chapter's reckoning, most of those houses were built with at least one masonry chimney, often two, and plenty of them have been reroofed around the stack without the flashing ever being properly renewed.

The usual finding is not a hole in the metal. It is a counterflashing that was face-nailed and sealed to the brick instead of being let into a mortar joint, or an apron whose sealant bead has split, or no back pan at all behind a wide chimney. Each of those admits water at a predictable rate and each one has a proper answer.

Service area
New Haven & New Haven County
Availability
Call to reach a local roofer
Warning signs

Signs you need chimney flashing repair

A chimney is the worst place on a roof to be inexperienced. Footing is poor, the stack itself may be unsound where the mortar has gone, and old bricks can move under a hand hold. Do not climb up to inspect it, and do not lean a ladder against the stack. From inside, note where the staining is relative to the chimney breast and photograph it with the date. If brick or mortar debris is falling into the fireplace, stop using it and call (833) 751-2102.

  • Staining on the ceiling or the wall immediately below the chimney breast
  • Damp bricks inside the house at the chimney, especially after a long storm
  • Rust streaks running down the stack from the flashing line
  • Sealant visible along the brickwork, cracked or peeling away from the masonry
  • A white crust or crumbling mortar on the stack where water has been sitting
  • Shingles lifted or cupped against the sides of the chimney
  • Debris and needles packed into the back of the chimney where a pan should drain
Job stories

Typical jobs for chimney flashing repair

Typical job
Illustration: A typical chimney joint check before winter

A typical chimney joint check before winter

What homeowners notice
A homeowner wants the roof looked at before the cold weather and mentions a faint mark on the ceiling of the room beside the chimney that has never been explained.
What we do
The joint is examined piece by piece: the base flashing, the step flashing up each side and the counter-flashing set into the mortar. Sealant smeared over a failed step course is removed and the joint is rebuilt in metal rather than patched.
What to expect
The findings describe each part of the joint, note the mortar condition for future reference, and record with photographs what was removed and what replaced it.

Options

Types and options for chimney flashing repair

Apron and step flashing renewal

The standard job on a chimney of ordinary width. New metal across the front, step pieces up both sides interleaved with the courses, and counterflashing into the joints. It is the detail that should have been built in the first place, and on many older houses it is the first time the stack has had it.

Adding a cricket behind a wide chimney

A wide stack sitting on a slope creates a flat shelf on its uphill side where water, snow and debris collect. A cricket is a small framed roof built into that space to divide the water and send it around both sides. Without one, the back of the chimney is a reservoir, and that is where most chimney leaks on wide stacks come from.

Repairs tied to masonry work

Where the mortar joints are too far gone to hold counterflashing, repointing or a crown repair has to happen for the flashing to be permanent. The sequencing matters: masonry first or in step with the roofing, so the metal is let into joints that will still be there in ten years.

Disused and abandoned stacks

An unused chimney still has to shed water, and the cheapest long-term answer is sometimes to take it down below the roof line and close the opening properly. That is a structural decision with other consequences, including appearance, so on a house in a local historic district it is a question for the commission, as the historic district roof work page describes.

One call and it gets handled.

Tell us when you need someone and we book the earliest visit a chimney flashing repair technician has, and you approve the price before any work starts.

Why does sealing the brickwork never last?

Because masonry, metal and wood all move at different rates with temperature, so a bead of sealant along a brick face is being stretched and compressed every day. It splits, and once it splits it channels water into the gap it was meant to close.

A properly cut counterflashing does not depend on anything sticking. The metal turns into the wall, so there is no exposed seam facing upward for water to sit in. That is a geometric solution rather than a chemical one, and it is why the method has not changed in a very long time.

The face-nailed and sealed version is quick, cheap and extremely common on older houses here. It usually gives a few years. When a homeowner reports that the chimney has been flashed twice already and still leaks, this is almost always what has been done.

What else sends water down a chimney?

The crown at the top, the absence of a cap, open mortar joints in the stack, and a flue liner that has failed. All of these take water into the chimney itself, where it emerges inside the house and looks exactly like a flashing leak.

A cracked crown is the most frequent of these. It is the slab at the top of the stack, it takes the full weather, and when it splits water runs straight into the masonry and down inside. A missing cap lets rain fall directly down the flue, which on a disused chimney has nowhere to go but into the brick.

This is why a roofer will ask about the top of the chimney before talking about the flashing. Chimney work above the roof line is often a masonry or sweeping matter rather than a roofing one, and spending money on new flashing while the crown is open is money wasted.

  • Flashing failure: staining appears where the stack passes through the roof
  • Crown or cap failure: damp bricks inside, often at a lower floor as well
  • Open mortar joints: damp patches that follow long, wind-driven rain
  • Condensation in a disused flue: staining with no rain to explain it

How does the chimney tie into winter problems?

In two ways. The stack interrupts the slope, so snow drifts and meltwater collect on its uphill side and freeze there. And the chase around a chimney inside the house is often an open air path from the basement to the attic, delivering warm air straight to the roof deck.

The first of those is a drainage problem solved with a cricket and a clear back pan. The second is an air-sealing problem, and it is one of the largest single leaks in many older houses, because the gap around a masonry chimney was traditionally left open for clearance.

Sealing that gap needs non-combustible material and careful detailing, not expanding foam, and it is usually done as part of the attic work described on the attic ventilation for ice dams page. The winter consequence of not doing it is on the ice dam removal and repair page.

When is chimney flashing done as part of a bigger job?

Almost always during a replacement, because the courses are off anyway and the metal can be built as a set from scratch. Doing it then is far better value than doing it later, and a scope that leaves the old flashing in place around a new roof is a scope worth questioning.

A new covering laid around old chimney metal gives you a roof whose weakest point is as old as the one you just removed. It is the clearest example of why flashing should be priced as part of the work rather than as an extra, and it is worth asking about explicitly before the job starts.

The same logic applies to a slate roof being repaired around a stack. The stone has to come up to get at the metal, so if the metal is near the end of its life, that is the moment. The hand techniques for taking slate up and resetting it are on the slate roof repair page.

Our process

How our chimney flashing repair visit works

  1. Separate roof water from chimney water

    Water can enter at the flashing or down the inside of the stack through a cracked crown, a missing cap or open mortar joints. The two look identical from the room below. A roofer establishes which it is before anything is renewed, since replacing flashing will not stop water coming down a flue.

  2. Look at the masonry condition

    Counterflashing has to be let into a sound mortar joint, so the state of the brickwork decides what can be done. Badly weathered joints or spalling brick mean masonry work comes first or alongside, and that is a different trade with its own scope.

  3. Strip the old metal and the courses around it

    Shingles or slates are lifted on all sides of the stack so the flashing can be rebuilt as a set rather than patched in pieces. Old sealant and tar are removed, which is often the slowest part on a chimney that has been worked on repeatedly over the years.

  4. Build the detail in the right order

    An apron goes across the downhill face, step pieces are woven one per course up each side, and a pan or cricket handles the uphill face. Each piece is lapped so water runs out onto the covering, and nothing relies on adhesive to keep water out.

  5. Cut the counterflashing into the joint

    A groove is cut into a mortar joint, the upper edge of the metal is turned into it, and the joint is repointed to hold it. That is what makes the top edge permanent, because the water runs down the brick, meets metal that is inside the wall rather than stuck to its face, and is thrown out onto the apron.

  6. Reset the covering and check the drainage

    The courses go back around the new metal, lapped so the flashing is covered where it should be and exposed where it should be. Debris is cleared from behind the stack, because a back pan that cannot drain holds water against the masonry all winter.

New Haven County

Why chimney flashing repair is different in South Central Connecticut

Masonry chimneys are a given on the older housing in this area. The city's own housing chapter puts well over a third of its homes before World War II, and houses of that period commonly carry one or two brick stacks, sometimes wide ones serving several flues. Wide stacks on a sloped roof are exactly the case where a cricket is needed, and exactly the case where one is most often missing.

In the Naugatuck valley towns the stock is denser and older still in places. Ansonia grew around copper, brass and rubber mills on the river from the 1840s, and Seymour's downtown developed into the 1920s, leaving dense 19th and early 20th century building. Chimneys on houses of that age have often been repointed more than once, and the condition of the joints decides whether counterflashing can be cut in today.

Weather here works on a chimney from two directions. Long nor'easters drive rain horizontally against the masonry, which finds any upward-facing seam; winter cold and thaw cycles break down mortar joints and crowns year by year. On the shoreline, in West Haven and East Haven, salt in the air adds to the corrosion of the exposed metal at the flashing line.

Related

Roof Repair

A failed section of roof is found, scoped and rebuilt, rather than the whole covering being torn off.

Attic Ventilation for Ice Dams

Air sealing and balanced venting stop the roof deck being warmed from below, which is what starts an ice dam.

Historic District Roof Work

Material and appearance are reviewed in a local district, so the sequence runs review first, order second, work third.

Guides

Read before you book

FAQ

Chimney Flashing Repair FAQs

Can the flashing be repaired without taking shingles off?

A short-term patch can be put on from above, and it is a holding measure rather than a repair. Step flashing works because each piece is interleaved with a course, so the only way to install it properly is to lift the covering on each side of the stack. A job that promises otherwise is promising a bead of sealant.

Do I need a mason as well as a roofer?

Sometimes. If the joints are sound, a roofer cuts in the counterflashing and repoints that line as part of the work. If the stack is generally weathered, the crown is cracked, or brick is spalling, masonry work is its own job and the flashing should be done in step with it rather than before.

What is a cricket and do I need one?

It is a small framed roof built behind a chimney to split water around the stack instead of letting it pond against the uphill face. Whether yours needs one depends on the width of the chimney and the pitch of the roof, and a roofer standing on the roof can tell you in a minute.

My chimney is not used any more. Can it just be sealed?

It still has to shed water and still has to be capped, because an open flue is a hole in the roof. Capping it is straightforward; taking it down below the roof line is sometimes the better long-term answer, and that is a structural and appearance decision rather than a quick fix.

The staining is at a lower floor, not the top. Is it still the roof?

It can be, since water inside masonry travels downward and emerges where the brick is coldest or the plaster is thinnest. It can equally be the crown or the joints high on the stack. That is why the diagnosis looks at both the flashing and the top of the chimney before anything is renewed.

Should this wait until the whole roof is replaced?

If the roof has years left, no: an active chimney leak is wetting timber now. If the covering is near the end anyway, doing the flashing as part of the replacement is better value and a better result. A roofer who has looked at both can tell you which situation you are in.

WhatsApp